Determination of chromium in foodstuffs by using novel adsorbent in vortex assisted-dispersive solid phase micro-extraction method: An application of multivariate techniques.

A new graft copolymer composed of polystyrene and polylinoleic acid (PLinas) with the sodium salt of iminodiacetate (Ida) was synthesized and used as an adsorbent. The vortex-assisted dispersive solid-phase micro-extraction (VA-dSPµE) method was used for the extraction and pre-concentration of chromium. Multivariate methodologies, such as factorial design and 3D surface plots, were applied for screening and optimizing effective extraction parameters. The influence of diverse analytical parameters, such as pH, sample volume, and interfering ions, on the extraction of chromium was studied. The calibration standard curve exhibited a linear range from 0.01 to 0.50 µg L-1. The relative standard deviation and limit of detection were found to be 1.65 % and 0.003 µg L-1, respectively. Extraction recoveries were found in the range of 96 to 99 % by using certified reference materials (CRMs). The adsorbent capacity of PLinas-Ida was found to be 112 mg g-1. The VA-dSPµE method demonstrated its effectiveness in the pre-concentration and determination of chromium within samples of foodstuffs by graphite furnace-atomic absorption spectrometry (GF-AAS).

CoSn(OH)6 nanocubes as a solid sorbent for the effective preconcentration of copper ions in cinnamon (Cinnamomum zeylanicum) extract.

This study was aimed at developing a simple and efficient CoSn(OH)6 nanocubes-based preconcentration method for the preconcentration of copper ions from cinnamon extracts for determination by flame atomic absorption spectrometry. The cube-shaped sorbent was synthesized using the simple stoichiometric co-precipitation method under ambient conditions. Experimental factors of the method were evaluated with a comprehensive optimization approach to maximize the extraction efficiency for the analyte. Under the optimal conditions, the limit of detection (LOD), limit of quantitation (LOQ), and linear dynamic range were recorded as 0.98 µg/L, 3.28 µg/L, and 4.0-75 µg/L, respectively. The enhancement factor was calculated as 101.6-fold by comparing the LODs of the optimized and direct analysis systems. Percent recoveries were found to be within an acceptable range (77.6-115 %), with high repeatability using matrix matching calibration strategy. Results validated the proposed method as a highly efficient extraction approach for the monitoring of copper ions in herbal cinnamon extracts.

Switchable hydrophilicity solvent-assisted solidified floating organic drop microextraction for separation and determination of arsenic in water and fish samples.

The aim of the current study was to separate and determine arsenic in water and fish samples using a novel and green solidified floating organic drop microextraction (SFODME), which is based on switchable hydrophilicity solvent (SHS)-assisted procedure followed by hydride generation atomic absorption spectrometry (HG-AAS). The 4-((2-hydroxyquinoline-7-yl)diazenyl)-N-(4-methylisoxazol-3-yl)benzene sulfonamide (HDNMBA) and tertiary amine (4-(2-aminoethyl)-N,N-dimethylbenzylamine (AADMBA) were used as ligand and SHS, respectively. The use of SHS promotes quantitative extraction of arsenic complexes into an extraction solvent (1-undecanol). Some factors that impact extraction recovery were studied. Under optimal conditions, the limit of detection (LOD) and limit of quantification (LOQ) were 0.005 µg L-1 and 0.015 µg L-1, respectively. The calibration graph was linear up to 900.0 µg L-1 arsenic, with the enrichment factor is 267. The proposed SHS-SFODME methodology for arsenic quantification in water and fish samples was successfully implemented. The environmental friendliness and safety of proposed method were approved by the Analytical Greenness Calculator (AGREE) and the Blue Applicability Grade Index (BAGI) tools.

Molecular engineering of a new method for effective removal of cadmium from water.

Cadmium (Cd) is a widespread and highly toxic environmental pollutant, seriously threatening animal and plant growth. Therefore, monitoring and employing robust tools to enrich and remove Cd from the environment is a major challenge. In this work, by conjugating a fluorescent indicator (CCP) with a functionalized glass slide, a special composite material (CCPB) was constructed to enrich, remove, and monitor Cd2+ in water rapidly. Then Cd2+ could be effectively eluted by immersing the Cd-enriched CCPB in an ethylenediaminetetraacetic acid (EDTA) solution. With this, the CCPB was continuously reused. Its recovery of Cd2+was above and below 100 % after multiple uses by flame atomic absorption spectrometry (FAAS), which was excellent for practical use in enriching and removing Cd2+ in real aqueous samples. Therefore, CCPB is an ideal material for monitoring, enriching, and removing Cd2+ in wastewater, providing a robust tool for future practical applications of Cd enrichment and removal in the environment.

Disruption of a three-component solution as a novel strategy for Cu and Ni extraction from vegetable oils for their determination by GF AAS.

In this work, we propose a novel approach for extracting Cu and Ni from vegetable oils (which can be expanded to other metals). The method is based on the transference of the analytes to an aqueous acid phase due to the disruption of a three-component solution. The extraction was carried out in two steps. In the first step, a three-component solution was prepared comprising the sample, 1-octanol, and HNO3 solution. Next, the homogeneous system was disrupted by adding 1.0 mL of deionized water, and two phases were formed. The aqueous extract deposited in the bottom of the flask was collected with a micropipette, and Cu and Ni were determined by graphite furnace atomic absorption spectrometry (GF AAS). The developed method presented limits of quantification (LOQ) of 0.25 and 0.17 ng g-1 for Cu and Ni, respectively, and was successfully applied in the analysis of eleven oil samples from different origins.

Coordination polymer gel mediated spectrophotometric, ICP-AES and spectrofluorimetric methods for trace As(III) determination in water and food samples.

Herein, a coordination polymer gel is proposed for the determination of As(III) in real samples through multispectroscopic techniques viz. spectrophotometry, spectrofluorimetry, and inductively coupled plasma atomic emission spectroscopy (ICP-AES). Taguchi L32 (46 21) design and adaptive neuro fuzzy inference system (ANFIS) optimized the controllable factors affecting the extraction yielding an experimental S/N ratio of 39.94 dB. The fluorescence quenching (KSV = 2.63 × 106 L mol-1) was static with photoelectron transfer being the main mechanism confirmed by the density functional theory calculations. The limits of detection (LODs), limits of quantification (LOQs) and linear ranges were 0.038 µg L-1, 0.13 µg L-1 and 1.67-116.67 µg L-1, 0.40 µg L-1, 1.21 µg L-1 and 1.67-33.33 µg L-1, 1.07 µg L-1, 3.24 µg L-1 and 3.32-35.37 µg L-1 for the developed enrichment coupled ICP-AES, spectrophotometry and fluorescence sensing methods. Among these methods, the enrichment - ICP-AES method has the lowest LOD, LOQ and the widest linear range followed by the enrichment - spectrophotometry and fluorescene sensing methods. Spectrofluorimetry offers high sensitivity, selectivity, and possible real time monitoring, spectrophotometry provides a cost-effective and versatile option, while ICP-AES manifests multi-element analysis with high sensitivity and low interference. The developed methods were validated and employed for the successful determination of trace As(III) in real samples. The employment of these methods enhances the overall analytical capability for a wide range of sample types and concentrations.

Micro solid phase extraction of lead and cadmium using functionalized nanodiamonds@CuAl2O4@HKUST-1 nanocomposite for FAAS analysis in food and water samples.

This study focuses on the development and application of a novel nanocomposite (functionalized nanodiamonds@CuAl2O4@HKUST-1)-based µ-SPE method for the sensitive and selective extraction of Pb and Cd from food and water samples. The technique offers high sensitivity and selectivity, allowing accurate measurement of these metals at trace levels. The detection limit is 0.031 µg kg-1 for Cd and 0.052 µg kg-1 for Pb, with a relative standard deviation of 1.7 % for Cd and 4.8 % for Pb. The method was successfully applied to real samples and efficiently quantified Pb and Cd in food and natural water samples. The highest concentrations were found in red lentils (0.274 µg kg-1 Pb) and fresh mint (0.197 µg kg-1Cd), but still below recommended limits set by FAO/WHO (300 µg kg-1 for Pb and 200 µg kg-1 for Cd). It promises to ensure food safety, monitor environmental contamination, and informs regulatory decisions to protect public health.

Determination of copper in rose tea samples using flame atomic absorption spectrometry after emulsification liquid-liquid microextraction.

Rose tea infusion has gained popularity worldwide due to its health benefits. However, it is known that tea plants can be contaminated with heavy metals including copper. Hence, an accurate and applicable analytical method namely emulsification liquid-liquid microextraction based deep eutectic solvent - flame atomic absorption spectrometry (ELLME-DES-FAAS) was proposed to determine copper at trace levels in rose tea samples. Under the optimum experimental conditions, analytical figures of merit for the developed method were examined, and dynamic range, limit of detection (LOD) and limit of quantification (LOQ) were found to be 5.07-246.61 µg/kg (mass-based) with 0.9992 coefficient of determination, 2.50 µg/kg and 8.32 µg/kg, respectively. A matrix matching calibration strategy was employed to boost recovery results, and the acceptable recovery results were recorded between 95.9 % and 118.4 %. According to recovery results, the developed analytical method can be safely employed to determine the concentration of copper in rose tea samples accurately.

Determination of copper ion at trace levels in apple tea samples by simultaneous complexation and spray assisted microextraction method prior to detection by flame atomic absorption spectrophotometry.

In the present study, a green and sensitive analytical method for the determination of copper ion at trace levels in apple tea samples was developed. Simultaneous complexation/extraction of the analyte were achieved by spraying-based fine droplet formation liquid-phase microextraction (SFDF-LPME). Copper ion was complexed with a Schiff base chelating agent called as N,N'-Bis(salicylidene)-1,2-phenylenediamine (BSP). Under the optimum conditions, the developed SFDF-LPME-FAAS and FAAS system were assessed with respect to limit of detection (LOD), limit of quantitation (LOQ), linearity and percent relative standard deviation (%RSD). LOD and LOQ values for SFDF-LPME-FAAS method were found to be 6.0 and 19.9 µg/kg, respectively. Enhancement in calibration sensitivity for developed method was found as 23 folds. In addition, accuracy/suitability of the developed SFDF-LPME-FAAS method were confirmed by spiking experiments. Two different apple tea samples were spiked to different concentration values and percent recovery results from 91.1 and 123.8 % proved the accuracy/suitability of the method.

A green and simplified approach for the quantitative and sensitive analysis of heavy metal ions in sea and stream waters.

Elimination of the matrix effect is a major challenge in developing a method for the quantification of heavy metals (HMs) in water samples. In this regard, the current research describes the simultaneous analyses of Cu(II), Cd(II), and Ni(II) ions in water matrices through flame atomic absorption spectrophotometry (FAAS) after preconcentration with carrier element-free co-precipitation (CEFC) technique by the help of an organic co-precipitant, 3-{[5-(4-Chlorobenzyl)-3-(4-chlorophenyl)-1H-1,2,4-triazol-1-yl]-methyl}-4-[2,4-(dichlorobenzylidene)amino]-1H-1,2,4-triazole-5(4H)-thione (CCMBATT). Based on our literature research, CCMBATT was employed for the first time in this study as an organic co-precipitant for the preconcentration of HMs. Factors such as solution pH, concentration of co-precipitant, sample volume, standing time, centrifugation rate, and time were thoroughly examined and optimized to achieve the highest efficiency in terms of HM recovery. The limits of detection (LODs) (with 10 number of tests) of 0.54, 0.34, and 1.95 µg L-1 and the relative standard deviations (RSD %) of 2.1, 3.3, and 3.0 were determined for Cu(II), Cd(II) and Ni(II) ions, respectively. Recovery results of HMs for the spiked samples were in the range of 92.8-101.0%, demonstrating the trueness of the method and its applicability to the water samples matrix.

Mercury determination in various environmental, food and material complex matrices using unified operating conditions for a cold vapor generation high-resolution continuum source quartz tube atomic absorption spectrometry method.

An analytical method with broad applicability based on cold vapor generation high-resolution continuum source quartz tube atomic absorption spectrometry was developed and evaluated for the determination of total mercury in matrices with various complexities and compositions. Sample preparation for different matrices of food, environmental samples and (bio)polymeric materials and unified operating conditions for derivatization and measurement were evaluated. The method was validated according to established requirements (Eurachem Guide 2014, EC Decisions 657/2002; 333/2007; 836/2011 and Association of Official Analytical Chemists Guide - AOAC). Analytical versatility was checked on various samples of fish fillets, mushrooms, soil, water and water sediment, sludge from a wastewater treatment unit, and (bio)polymeric materials from waste recycled from food packaging, computers and garden tools. Under optimal conditions for cold vapor generation in a batch system, namely 3% (v/v) HCl as reaction medium for 5 mL aliquot samples and a volume of 3.5 mL 0.3% (m/v) NaBH4 stabilized in 0.2% (m/v) NaOH as derivatization reagent, the detection limit for Hg in terms of peak height measurement (n = 7 days) was in the range 0.064 ± 0.004 µg L-1 in water, 0.014 ± 0.001 mg kg-1 in environmental samples and 0.009 ± 0.001 mg kg-1 in (bio)polymeric materials. Overall recovery of Hg by analysis of certified reference materials was 102 ± 20% (k = 2) in food, soil, wastewater and water sediment, and polyethylene. Precision for the measurement of various real samples ranged between 4.2 and 15.0%. A performance study highlighted that the method was sensitive, free of non-spectral interference coming from the multielemental matrix and that it complied with the requirements for Hg determination set in EC Decisions and AOAC Guidelines at least for the more common matrices analyzed for social impact.

Analytical application of flower-shaped nickel nanomaterial for the preconcentration of manganese in domestic wastewater samples.

In this study, detection sensitivity of the conventional flame atomic absorption spectrophotometer (FAAS) for the determination of manganese (Mn2+) was enhanced by employing a preconcentration method from wastewater samples. Flower-shaped Ni(OH)2 nanomaterials were synthesized and used as sorbent material in preconcentration procedure. With the aim of attaining optimum experimental conditions, effective parameters of extraction method were optimized and these included pH of buffer solution, desorption solvent concentration and volume, mixing type and period, nanoflower amount, and sample volume. The detection limit of the optimized method was determined to be 2.2 µg L-1, and this correlated to about 41-fold enhancement in detection power relative to direct FAAS measurement. Domestic wastewater was used to test the feasibility of the proposed method to real samples by performing spike recovery experiments. The wastewater sample was spiked at four different concentrations of manganese, and the percent recoveries determined were in the range of 95-120%.

Quantitative analysis of Cd based on the stress effect of minerals in rice by laser-induced breakdown spectroscopy.

Cadmium (Cd) is a highly toxic heavy metal that can accumulate in the food chain, posing a significant threat to human health. One of the key food sources through which Cd is often observed is rice. Therefore, determining heavy metals in rice is essential to assess the risk status of rice. Laser-induced breakdown spectroscopy (LIBS) has the advantages of simple sample preparation and fast analysis, which is expected to achieve real-time and rapid detection of rice. In this work, 40 naturally matured rice samples growing from the area that is possibly contaminated with Cd were collected to determine the Cd reference content in rice by graphite furnace atomic absorption spectroscopy as recommended by the Chinese National Standard. LIBS spectral acquisition and analysis are adopted as well. The Cd characteristic spectral lines were selected to predict the Cd content directly using PCA, PLSR, and ELM models, and the coefficient of determination (R2) of the models' training and prediction sets was 0.9278, 0.8920; 0.9036, 0.9771; 0.7940, and 0.8409, respectively. Further, based on the Cd stress effect in rice, the spectra of elements Mn, Mg, K, and Na with highly significant and significant correlation with Cd were selected and coupled with the Cd characteristic spectra to form a new matrix of the same size for quantitative analysis. Based on the stress effect, R2 of models' training and prediction sets was improved to 0.9786, 0.9753; 0.9395, 0.9900; 0.9798, and 0.9927, respectively. It is demonstrated that combining the stress effect when using LIBS for quantitative analysis of Cd in rice reduces the overfitting and further improves the model's prediction accuracy. This work indicates that using LIBS combined with suitable mathematical models to predict the Cd content of naturally matured rice based on stress effects in rice is feasible. It is promising to evaluate the safety of rice by analyzing LIBS spectra.

A new method for extraction and pre-concentration of the heavy metals using a microemulsion system in winsor II equilibrium and determination by HR-CS AAS.

For the very first time, a microemulsion system in the Winsor II (WII) equilibrium was applied in a sample preparation method for extraction and pre-concentration in the determination of Pb, Cd, Co, Tl, Cu and Ni, in natural waters by high resolution continuum source atomic absorption spectrometry (HR-CS AAS). The method was optimized using the graphite furnace atomization. A simplex-centroid design for determine optimum extraction condition (77.5% aqueous phase, 5% of the oil phase, and 17.5% cosurfactant/surfactant ratio - C/S = 4) was applied. The optimized time for the sample preparations was around 30 min. The analytical performance of the optimized method using HR-CS GF AAS showed that the detection limits were: 0.09, 0.01, 0.06, and 0.05 µg L-1 for determination of Pb, Cd, Tl, and Co, respectively and the enrichment factors were between 6 and 19, considered excellent for all analytes. The RSD values were lower than 5%, demonstrating the good precision of the proposed method. When the optimized method was applied using the HR-CS F AAS, the sensibility increased 9 to 12 times for Cu and Ni, respectively. The analytical method was successfully applied for the determination of analytes in Certified Reference Material and real samples for natural waters such as Brackish water (recovery between 107 and 112%), Saline water (recovery between 83 and 94%), Produced water from oil industry (recovery between 98 and 110%) and Fresh water (recovery 80 and 87% to Cu and Ni respectively). All the results confirming the accuracy of the analytical method proposed. The repeatability of the measurements has been better 5% (n = 3), for all elements.

A magnetic solid phase extraction procedure for Pb(II) at trace levels on magnetic Luffa@TiO2 in food and water samples.

A novel magnetic Luffa@TiO2 sorbent was synthesized and characterized by using XRD, FTIR and SEM techniques. Magnetic Luffa@TiO2 was used for solid phase extraction of Pb(II) in food and water samples prior to its flame atomic absorption spectrometric (FAAS) detection. The analytical parameters such as pH, adsorbent quantity, type and volume of eluent, and foreign ions were optimized. Analytical features such as the limit of detection (LOD) and the limit of quantification (LOQ) of Pb(II) are 0.04 µg L-1 and 0.13 µg L-1 for liquid samples and 0.159 ng/g and 0.529 ng/g for solid samples, respectively. The preconcentration factor (PF) and relative standard deviation (RSD%) were found 50, and 4 % respectively. The method was validated by using three certified reference materials (NIST SRM 1577b bovine liver, TMDA-53.3 and TMDA-64.3fortified water). The presented method was applied to lead contents of some food and natural water samples.

A simple microwave-assisted synthesis of cobalt ferrite nanoparticles and its application for the determination of lead ions in rooibos (Aspalathus linearis) tea.

In this study, a magnetic sorbent assisted dispersive solid phase extraction (DSPE) method was used to preconcentrate lead ions from rooibos tea samples for determination by slotted quartz tube-flame atomic absorption spectrometry (SQT-FAAS). Cobalt ferrite magnetic nanoparticles (CoFe2O4 MNPs) were synthesized by microwave assisted digestion. Limits of detection and quantification were calculated as 5.3 and 17.6 µg/L, respectively, in a linear dynamic range of 20-800 µg/L. The enhancement factor of the developed method was found to be 80-folds when compared to the detection limit of the regular FAAS system. The percent recoveries obtained for rooibos tea samples spiked at different concentrations were in the range of 77 - 125%, with high repeatability as indicated by low standard deviations. The findings of the study demonstrated that the CoFe2O4 MNPs-based extraction method is a straightforward, fast, affordable, safe, and eco-friendly approach to qualifying/quantifying lead with high precision in the selected beverage sample.

Hyphenated liquid electrode glow discharge-dielectric barrier discharge molecular emission spectrometry for determination of dithiocarbamates.

A hyphenated liquid electrode glow discharge (LEGD)-dielectric barrier discharge (DBD) molecular emission spectrometer was constructed and used as a novel liquid chromatography (LC) detector for dithiocarbamates (DTC) determination. The LEGD was used as an acidolysis reactor for the in-situ transformation of DTCs into CS2 with high efficiencies of 74.11-97.98%. The DBD was used to excite CS2 gas to generate a specific molecular emission at 257.94 nm. The linear correlation coefficient of the method was > 0.99 from 1 to 200 µg mL-1. The detection limits ranged from 0.1 to 0.3 µg mL-1 with 76-119% recovery and relative standard deviations of 0.2-8.5%. Moreover, the hyphenated microplasma spectrometer achieved low power consumption, low temperature, immediate acidolysis, and high transformational efficiency, and can detect each DTC when combined with LC.

Trace nickel determination in seawater matrix using combination of dispersive liquid-liquid microextraction and triethylamine-assisted Mg(OH)2 method.

In order to eliminate the effects of seawater matrix on the precise/accurate determination of elements, new and efficient analytical procedure requires. In this study, co-precipitation method based on the triethylamine (TEA)-assisted Mg(OH)2 was performed to eliminate side-effects of seawater medium on the determination with flame atomic absorption spectrometry (FAAS) prior to the preconcentration of nickel by an optimized dispersive liquid-liquid microextraction (DLLME) method. Under the optimum conditions of the presented method, the limit of detection and quantification (LOD, LOQ) values obtained for nickel were found as 16.1 and 53.8 µg kg-1, respectively. Seawater samples collected from West Antarctic region were used for real sample applications to check the accuracy and applicability of developed method, and satisfying recovery results (86-97%) were obtained. In addition to this, the digital image-based colorimetric detection system and the UV-Vis system were applied to confirm the applicability of the developed DLLME-FAAS method in other analytical systems.

Biohybrid Adsorbent for the Preconcentration of Lead and Its Determination in Fruit Juices by Electrothermal Atomic Absorption Spectrometry.

BACKGROUND: Fruit juices are one of the most non-alcoholic beverages consumed in the world. Essential elements and other nutrients present in fruit juices play an important role in human well-being. However, fruit juices may also contain potentially toxic elements at trace levels, causing health risks. OBJECTIVE: The objective of this work was to develop an analytical methodology based on the preconcentration of lead using a new biodegradable hybrid material (BHM) composed of Rhodococcus erythropolis AW3 bacteria and Brassica napus hairy roots. METHODS: The BHM was implemented in an online solid-phase extraction (SPE) system for the determination of lead in fruit juices by electrothermal atomic absorption spectrometry (ETAAS). RESULTS: Effects of critical parameters on lead retention were studied. Under optimal experimental conditions, extraction efficiency higher than 99.9% and an enrichment factor of 62.5 were achieved. The dynamic capacity of the BHM was 36 mg/g, which favored the reuse of the column for at least eight biosorption-desorption cycles. The LOD and LOQ for preconcentration of 5 mL of sample were 5.0 and 16.5 ng/L lead, respectively. The RSD was 4.8% (at 1 µg/L lead and n = 10). CONCLUSION: The developed method was suitable for application to lead determination in different types of fruit juice. HIGHLIGHTS: A novel microextraction procedure based on the use of a biohybrid adsorbent. Highly sensitive determination of Pb at trace levels. Analysis of Pb in fruit juices samples. An eco-friendly microextraction technique for Pb determination.

Ultrasound assisted dispersive solid phase microextraction using polystyrene-polyoleic acid graft copolymer for determination of Sb(III) in various bottled beverages by HGAAS.

A new polyoleic acid-polystyrene (PoleS) block/graft copolymer was synthesized and applied as adsorbent for ultrasound assisted dispersive solid phase microextraction (UA-DSPME) of Sb(III) in different bottled beverages and analysis using hydride generation atomic absorption spectrometry (HGAAS). Adsorption capacity of the PoleS was 150 mg g-1. Several sample preparation parameters such as sorbent amount, solvent type, pH, sample volume and shaking time were optimized (based on central composite design (CCD) approach) and evaluated in respect to the recovery of Sb(III). The method revealed a high tolerance limit of matrix ions presence. Under optimized conditions, linearity range, the limit of detection, the limit of quantitation, extraction recovery, enhancement factor, preconcentration factor were 5-800 ng L-1, 1.5 ng L-1, 5.0 ng L-1, 96%, 82, 90, respectively. Accuracy of the UA-DSPME method was confirmed based on different certified reference materials and standard addition method. Factorial design was utilized to estimate the influences of variables of recovery of Sb(III).